Fantech HRV ATMO 150H Air Exchanger | Montreal, Laval, Longueuil, South Shore and North Shore

In stock
SKU: ATMO 150H
161 cfm net1,900 to 3,000 sq ft60% at −25 °C
Talk to an HVAC technician · 514 316-2973
Meets the Québec CodeLifetime core warranty
01 · Your home

Is it the right size for your home?

It delivers 161 cfm net, enough to ventilate 1,900 to 3,000 sq ft. Choose your home's living area.

It's the right size.

For a 2,500 to 3,200 sq ft home, about 150 cfm of air needs to be renewed continuously. This unit delivers 161 cfm net — enough for the house, with extra capacity to boost ventilation for the bathroom and kitchen.

Calculation: 0.35 air changes per hour over the living volume, with 9 ft ceilings. Our estimator sets the exact airflow room by room, following CSA F326.

02 · Performance

What it does, in numbers

Heat recovery
60%
At −25 °CCode: 54% minimum
74%
At 0 °CCertified at 64 cfm
Net airflowThe ducts cost it 25 cfm
0.2 in · test bench186 cfm
0.4 in · with ducts161 cfm

$52.71

Electricity per year

Less than a 60 W light bulb

Bulbs left on day and night. Same calculation for every line: wattage × 8,760 h × 11.142 ¢/kWh.

54W
Running continuously
473kWh
Per year
3months
Filter cleaning

Meets the Québec Construction Code everywhere in the province. The Code requires 54% at −25 °C below 6,000 degree-days (Montréal, Laval, Longueuil and both shores) and 60% above that. This unit is rated at 60% at 66 cfm.

Airflow and efficiency at 0 °C and −25 °C: HVI directory, Section III. Cost: 54 W over 8,760 h at Hydro-Québec's Rate D second tier (11.142 ¢/kWh).

03 · Good to know

What you should know about this one

Published, verifiable facts, not brochure claims.

17 inCore removal: 17 in in front of the door

The ATMO 150H's core comes out through the front door, held by two latches under the unit. Fantech calls for 17 in (432 mm) free in front of the unit to pull it out, and 2 3/8 in above the electrical box for wiring.

ISF6 in ISF collars that slide off

The ATMO 150H's four 6 in round collars are part of the ISF system: a collar is removed by sliding it toward the door, the duct is attached, and the collar is put back with its screws. Fantech says to use only the screws supplied with the collars.

60%What it still recovers at −25 °C

The only efficiency figure that matters for a Québec winter, and the one the Code uses. An efficiency quoted without its temperature means nothing; this one is measured at a test airflow of 66 cfm.

ExhaustIt defrosts by pausing the fresh air for a few minutes

In cold weather, the supply fan stops for a few minutes while the exhaust keeps running, so warm indoor air thaws the core. During the cycle the house is briefly under negative pressure; if you have a fireplace or a naturally vented combustion appliance, mention it to our estimator.

HRVIt recovers heat, not moisture

Excess moisture leaves the house. In Québec, that's the right choice in most cases: in winter, a home almost always has too much humidity, not too little.

2505290Its HVI certification number

Listed in Section III of the Home Ventilating Institute's certified products directory. Anyone can check it.

−25 cfmWhat the ducts cost it

Between a nearly unrestricted test bench (0.2 in) and a real duct system (0.4 in), it drops from 186 to 161 cfm.

54 WMeasured at the airflow it actually runs at

Its 74% at 0 °C is certified at 64 cfm, the continuous airflow of a typical home. At that setting it draws 54 W, or about 473 kWh a year.

LifetimeThe core warranty

The core does the work and is the most expensive part to replace. Motors: 7 years. Parts: 5 years.

6 inWhat it needs on site

6 in ducts, side connection and a condensate drain. It weighs 42 lb, and it needs enough clearance to slide the core out once a year.

Financial aid

Rénoclimat stopped funding HRVs and ERVs on October 1, 2026

Only files opened before that date, under the program's transition rules, remain eligible. This unit's HVI Section III certification (No. 2505290) remains the public proof of its performance: we balance it to the calculated airflow rather than running it at full speed.

04 · Installation

What it needs on site

6 in ductsCollar diameter
Side connectionSide ports
Condensate drainRequired
42 lbUnit weight
23.88 × 11.94 × 21.44 inLength × depth × height
120 VPower supply

In a condo with no floor drain, or with little ceiling clearance, we usually look at a side-port model instead. Our estimator checks the location, the drain and the duct route before ordering.

Complete spec sheetData and cited sources
Net airflow at 0.2 in. w.g.
186 cfm
Net airflow at 0.4 in. w.g.
161 cfm
SRE at 0 °C (64 cfm)
74%
SRE at −25 °C (66 cfm)
60%
ASE at 0 °C
80%
Power draw
54 W
Efficacy
1.2 cfm/W
Type
HRV
Connection
Side ports
Duct collars
6 in
Condensate drain
Required
Defrost cycle
Exhaust only (supply fan off)
Filters
2 washable electrostatic MERV 3 panel filters (10 × 11 7/8 in); optional MERV 8 (463943) and MERV 13 (463944)
Dimensions (L × D × H)
23.88 × 11.94 × 21.44 in
Weight
42 lb
Power supply
120 V
HVI certification (Section III)
2505290
Warranty — core
Lifetime
Warranty — motors
7 years
Warranty — parts
5 years
Spec sheet (French)
PDF
Spec sheet (English)
PDF

Net airflow, efficiency at 0 °C and −25 °C, and power draw: Home Ventilating Institute certified products directory, Section III (HVID 2505290). Annual consumption calculated at 54 W running continuously for 8,760 h, at Hydro-Québec's Rate D second tier (11.142 ¢/kWh), in effect since April 1, 2026.

05 · In the Fantech range

The next model down and up

Talk to an HVAC technician before you choose

We calculate the airflow room by room, check the location and the drain, and give you an installed price. Balancing is measured at commissioning, not estimated.

A side-port HRV for low ceilings

The Fantech ATMO 150H differs from the HERO units on one specific point: Fantech lists it among its side-port units, whereas the HERO units connect from the top. This heat recovery ventilator (HRV) is only 21.44 in. high and delivers a net airflow of 161 cfm at 0.4 in., and 186 cfm at 0.2 in.

It is the air exchanger to consider when the available height is limited, for example in a basement with a low ceiling or a narrow mechanical room: it is lower than every HERO unit.

Sliding ISF collars

The four 6 in. round collars on the ATMO 150H are part of Fantech's ISF system. To connect a duct, you slide the collar toward the door to remove it, attach the duct to it, then put the collar back in place with its screws. Fantech asks that only the screws supplied with the collars be used.

In a tight space, that is a real advantage. Fastening an insulated duct onto a collar already screwed to the unit, arms stretched into a corner of the ceiling, is often the most tedious step of an installation. With ISF collars, the duct is fastened to the collar before the collar goes back on the unit.

With the collars, the unit is 29 1/2 in. wide overall: that is the measurement to keep in mind when choosing the location.

Core removal: 17 in. in front of the door

The core comes out through the front door, which is held by two latches at the bottom of the unit. Fantech calls for 17 in. of clear space in front of the unit to remove it, and 2 3/8 in. above the electrical box for wiring.

Efficiency and power consumption

According to HVI, the sensible recovery efficiency of the ATMO 150H is 74% at 64 cfm and 0 °C, and its adjusted sensible efficiency is 80%. At −25 °C, it remains at 60% (measured at 66 cfm), above the 54% threshold of section 9.32 of the Québec Construction Code for Greater Montreal. The ATMO units use a cross-flow core, whereas the HERO units have a counterflow core: the HERO units recover a little more, the ATMO units win on size.

At the 64 cfm test point, it draws 54 W, or 1.2 cfm/W. Running continuously, that comes to about 473 kWh per year, roughly $53 at Hydro-Québec Rate D (11.142¢/kWh).

Defrost works by stopping the supply fan: fresh air stops coming in and the exhaust fan switches to high speed to clear the core with warm air from the house.

Installation

  • Dimensions: 23.88 × 11.94 × 21.44 in. (L × D × H)
  • Weight: 42 lb
  • Connections: 6 in., round, side
  • Power supply: 120 V
  • Drain: required, tube supplied

For an HRV, Fantech requires the drain tube to be installed. The unit hangs from the ceiling with the supplied chains and springs, or mounts on the wall on the bracket. The manual recommends short ducts, few elbows, 45° elbows and Y fittings rather than T fittings.

Filters and maintenance

Two washable electrostatic MERV 3 filters, 10 × 11 7/8 in., are supplied; they wash in warm soapy water. Fantech offers optional MERV 8 (463943) and MERV 13 (463944) filters. A finer filter reduces airflow: we take that into account when setting up the unit.

Warranty

Fantech warrants the core for life, the fan motors for 7 years, and the electrical components and the damper motor for 5 years. The unit is designed for residential use only.

The ATMO 150H is certified in section III of the HVI directory (number 2505290): its airflows and efficiencies are published and can be checked by anyone. Rénoclimat stopped funding HRVs and ERVs on October 1, 2026, except for files already opened under the program's transition rules.

Installation by AirGreen in Greater Montreal

We start with the room-by-room ventilation calculation under the CSA F326 standard. We then look at the available space: if a HERO unit does not fit in height, the ATMO 150H is often the answer.

At commissioning, we balance supply and exhaust with a manometer, to the calculated airflow. We install in Montreal, Laval, Longueuil, the North Shore and the South Shore.

For a free quote, call 514 316-2973 or write to sales@airgreen.ca.