Copper Pipe Clamp
The clamp that secures copper piping to a wall or structure, from 1/4 in to 1-3/8 in.
AirGreen codeAG-SP-01205
514 316-2973 · sales@airgreen.ca
Quick facts
The copper pipe clamp secures copper piping to a wall, a joist or the structure. It comes in eight diameters, from 1/4 in to 1-3/8 in, for heat pump refrigerant lines as well as mechanical room piping.
Why a refrigerant line needs proper support
A copper line left unsupported sags between its support points. Compressor vibration travels along it, the tube rubs against the wall and the fittings flex at every start-up. Over time, that is where leaks appear. Clamps installed at regular intervals keep the line straight, stable and quiet.
Eight diameters
The clamp is available for 1/4 in, 3/8 in, 1/2 in, 5/8 in, 3/4 in, 7/8 in, 1-1/8 in and 1-3/8 in piping. Choose the diameter based on the tube you are securing. Each size has its own AirGreen code, shown under the title when you select it.
Good fastening practices
- Space the clamps evenly, a little closer together on small diameters.
- Add a clamp near every elbow and every fitting.
- On an insulated line, do not compress the insulation: it would lose its effectiveness.
- Keep the copper away from contact with any other metal that could corrode it.
Supplied and installed by AirGreen in Greater Montréal
Our refrigeration technicians run and secure the refrigerant piping on every heat pump installation in Montréal, Laval, Longueuil, on the South Shore and on the North Shore. RBQ licence 5645-9605-01. For availability of a size or a quote, call us at 514 316-2973 or email sales@airgreen.ca with the diameter and quantity.
Straight, well-held piping
A poorly supported copper line sags, vibrates and ends up straining its fittings.
- Refrigerant lines of wall-mount, central and multi-zone heat pumps
- Runs along a wall, a joist or a basement ceiling
- Copper piping in a mechanical room
- Replacing rusted or broken clamps
8 sizes, one page
Each size has its own AirGreen code. Tap a row to select it.
| Diameter | AirGreen code |
|---|---|
| 1/4 in | AG-SP-01201 |
| 3/8 in | AG-SP-01202 |
| 1/2 in | AG-SP-01203 |
| 5/8 in | AG-SP-01204 |
| 3/4 in | AG-SP-01205 |
| 7/8 in | AG-SP-01206 |
| 1-1/8 in | AG-SP-01207 |
| 1-3/8 in | AG-SP-01208 |
Copper piping diameter, in inches.
Specifications
From the manufacturer’s documentation. A value the manufacturer does not publish is not listed.
What to know before installing
- Choose the clamp size from the copper tube you are securing.
- Space the clamps evenly, and close to changes in direction.
- On an insulated line, do not crush the insulation.
- Avoid direct contact between the copper and another metal that could corrode it.
You may also need
A.C.R. Soft Copper Tube – 50 ft Coil
Pre-Insulated Line Set for Wall-Mounted Heat Pump – 50 ft Roll
Armaflex Elastomeric Tube Insulation – 6 ft Length
Red Flashing – 10 ft Roll
Rubber Anti-Vibration Pads – Box of 48
Plastic End Caps for Wall Bracket – Box of 50
Protective Roof Extension for Two-Fan Units
3 in Thick Condenser PadBrackets and protectionSee all
Frequently asked questions
Which size do I need?
The size of the copper tube you are securing. A 3/8 in line takes a 3/8 in clamp.
How far apart should clamps go?
At regular intervals along the run, closer together on small sizes, and near elbows and fittings. The equipment manual sometimes gives a specific spacing.
Can I use it on an insulated line?
Yes, as long as the insulation is not crushed. An insulated line is fastened without compressing the foam.
Can you install it?
Yes. Our technicians secure the refrigerant piping on every heat pump installation, everywhere in Greater Montréal.
Copper lines held firmly in place
Tell us the size and the quantity: we confirm availability and send you a quote. Or let our technicians install it for you.
Specifications from the manufacturer’s documentation, checked on October 7, 2026.