Protective Roof for Heat Pump Outdoor Unit
The shelter that protects the outdoor unit from snow sliding off the roof, ice and freezing rain.
AirGreen codeAG-SP-01003
514 316-2973 · sales@airgreen.ca
Quick facts
The protective roof for outdoor units is installed above a heat pump's outdoor unit. It protects the unit from snow sliding off the roof, icicles falling from a gutter and freezing rain that coats the top of the unit. It is available in three sizes.
Whatever falls from the roof lands on the outdoor unit
In Montréal, many outdoor units end up under a sloped roof, a gutter or an upper-floor balcony. After a storm or a thaw, chunks of snow and icicles fall straight onto the unit. They can dent the casing, or damage the grille or the fan. Freezing rain, for its part, forms a crust of ice on top. The protective roof deflects all of this.
Three sizes
- Up to 18,000 BTU: for small-capacity outdoor units.
- 37 × 19 in
- 44 × 22 in
For a large unit with two fans, see our protective roof extension.
An installation that lets the unit breathe
The roof must not block the unit's air intake or discharge: it is installed while respecting the clearances required by the heat pump manufacturer. It protects the top of the unit, but does not replace proper height above the snow on the ground: a wall bracket or a ground stand is still needed where snow builds up.
Installed by AirGreen in Greater Montréal
Our refrigeration technicians install the protective roof when installing your heat pump or on an existing unit in Montréal, Laval, Longueuil, on the South Shore and on the North Shore. RBQ licence 5645-9605-01. For availability or a quote, call us at 514 316-2973 or email sales@airgreen.ca with the size and quantity.
A shelter from what falls off the roof
Under a sloped roof or an overhang, snow and icicles fall straight onto the outdoor unit.
- Outdoor units under a sloped roof or an eavestrough
- Spots exposed to freezing rain and falling ice
- Units on the ground, on a ground stand or on a wall bracket
- Protecting the fan and the top of the unit
3 sizes, one page
Each size has its own AirGreen code. Tap a row to select it.
| Size | AirGreen code |
|---|---|
| Up to 18,000 BTU | AG-SP-01001 |
| 37 × 19 in | AG-SP-01002 |
| 44 × 22 in | AG-SP-01003 |
Choose the size from the outdoor unit’s capacity or dimensions.
Specifications
From the manufacturer’s documentation. A value the manufacturer does not publish is not listed.
What to know before installing
- Choose the size from the outdoor unit’s dimensions, listed in its manual.
- The roof must not block air intake or discharge: keep the clearances the equipment maker asks for.
- It protects the top of the unit: it does not replace enough height above the snow on the ground.
- For a twin-fan unit, see the protective roof extension.
You may also need
Protective Roof Extension for Two-Fan Units
Wall Bracket for Heat Pump Outdoor Unit
Adjustable Ground Stand for Outdoor Unit
Rubber Anti-Vibration Pads – Box of 48
Copper Pipe Clamp
Plastic End Caps for Wall Bracket – Box of 50
3 in Thick Condenser Pad
Red Flashing – 10 ft RollLine sets, brackets, cover, drain, disconnect and cable on one page.See the kitSame category
Brackets and protectionSee all
Frequently asked questions
Which size do I need?
For a small unit, the up-to-18,000-BTU size. Otherwise, compare the outdoor unit’s dimensions with the 37 × 19 in and 44 × 22 in sizes. Send us the model and we tell you the right size.
Does the roof affect how the heat pump runs?
Not if it is installed with the clearances the equipment maker asks for, so air comes in and out freely.
Is it useful if the unit is not under the roof edge?
Less so. The protective roof is mainly for units under a sloped roof, an eavestrough or a balcony that sheds snow and ice.
Can you install it?
Yes. Our technicians fit it when they install your heat pump or on an existing unit, everywhere in Greater Montréal.
Protect your outdoor unit from winter
Tell us the size and the quantity: we confirm availability and send you a quote. Or let our technicians install it for you.
Specifications from the manufacturer’s documentation, checked on October 7, 2026.