THERMO 2000 VoltMax SCR VOLTSCR480180P3 Commercial Electric Boiler | 180 kW - 480V 3 Phase
At 180 kW on 480 V three-phase, Thermo 2000’s VoltMax SCR 180 is the largest size in configuration B: a commercial electric boiler for large buildings heated with hot water.
Model numberVOLTSCR480180P3
514 316-2973 · sales@airgreen.ca
Quick facts
180 kW on 480 V, the largest size in configuration B
For large buildings heated with hot water
Thermo 2000 groups its 99 to 180 kW VoltMax SCR boilers in a single configuration B. The VoltMax SCR 180 sits at the top: 180 kW, or 614,160 BTU/h, here in its 480 V three-phase version. It is a vertical commercial hot-water electric boiler whose output modulates from 0 to 100% through solid-state relays (SCR), alongside relay stages that the controller rotates.
It is meant for owners of heated warehouses, workshops and large commercial buildings, as well as the engineers and contractors who design or replace their heating. Its loop can serve radiators, hot-water baseboards, a radiant floor or hydro-air coils, and an indirect water heater through its second setpoint.
Planning an electrical load of this size
On 480 V three-phase, the VoltMax SCR 180 draws 216.5 A. A load of this scale is prepared with the engineer or the master electrician, who size the overcurrent protection and the conductors. This is where SCR modulation makes the most sense: rather than switching its output on in blocks, the boiler follows demand, which, according to Thermo 2000, limits peak power demand. If your building’s service is 600 V, the same boiler comes in that voltage.
Take a heated warehouse in Longueuil or on the South Shore. The boiler takes up little room there: 3 in of clearance on the sides and back, 24 in in front and 32 in above. On the hydronic side, it holds 30 US gal of water and connects through four 2 1/2 in NPT side connections; its setpoint runs from 50 °F to 200 °F. Its Schneider Electric controller communicates over BACnet IP and MS-TP, accepts a 0-10 Vdc signal and sends its alarms by email; its Incoloy immersion elements are replaceable.
What we take care of
The on-site estimate is free. We examine the electrical service, the loop and the access to the mechanical room, since the boiler weighs 550 lb (250 kg). The written quote then details the boiler, the circulating pump and the expansion tank, the last two being absent from Thermo 2000’s list of supplied items.
Our crews install the boiler, connect the piping and the 480 V circuit, fill and purge the loop, then set up the controller, the supplied outdoor sensor and, if needed, the link with the building management system. Thermo 2000’s warranty runs 10 years on the tank (limited warranty, closed-loop heating) and 2 years on the electrical and mechanical components. AirGreen, a family business established in Montreal for more than fifteen years, holds RBQ licence 5645-9605-01, which covers ventilation, refrigeration and electrical work.
Let’s discuss your building
Is your building in Longueuil, on the South Shore, in Montreal, Laval or on the North Shore? Ask for a free estimate and a written quote; financing is available.
A single 180 kW boiler for a large building on 480 V
The VoltMax SCR 180 delivers 614,160 BTU/h according to Thermo 2000, with SCR modulation from 0 to 100% that, per the manufacturer, limits peak power demand. This version runs on 480 V three-phase.
- Heated warehouses, workshops and large commercial buildings on 480 V
- Buildings whose heating load calls for the largest size in configuration B
- Radiator, baseboard, radiant floor or hydro-air coil loops
- Projects monitored by a building management system (BACnet IP / MS-TP)
Specifications
From the manufacturer’s documentation. A value the manufacturer does not publish is not listed.
What to know before installing
- 480 V three-phase, 60 Hz power supply: 216.5 A. A load of this size is planned with the engineer or master electrician, who size the overcurrent protection and conductors.
- The VoltMax SCR series also comes in 600 V: confirm the service voltage before ordering.
- The circulating pump and expansion tank are not on Thermo 2000’s list of supplied items.
- Clearances: 3 in on the sides and back, 24 in in front, 32 in above, none underneath. Weight: 550 lb (250 kg).
- Schneider Electric controller with backlit display
- Outdoor temperature sensor
- On/off control switch
- Control and power fuses and breakers
- SCR relays
- Two limit controls, automatic and manual reset
- Factory-installed relief valve
- Drain valve
- Low-water cutoff
Manufacturer documents
Explore the range
Electric boilersSee allSame brand
THERMO 2000See all
Frequently asked questions
Is a 180 kW boiler the right size for our building?
That depends on the building’s heat loss, calculated by the engineer or assessed during our visit. The VoltMax SCR comes in several outputs; we check the size before quoting.
What does SCR modulation bring to a 216.5 A load?
Instead of switching its output on in blocks, the boiler modulates it from 0 to 100% with solid-state relays, alongside relay stages. Thermo 2000 states that this modulation limits peak power demand.
Can it be linked to the building management system?
Yes. The Schneider Electric controller communicates over BACnet IP and MS-TP, accepts a 0-10 Vdc signal for setpoint and output, and its Ethernet port provides a web page and email alarms.
Can the heating elements be replaced?
Yes. Thermo 2000 uses replaceable Incoloy immersion elements. The controller’s alarm codes, displayed in French or English, help the technician make a diagnosis.
Which warranty applies?
Thermo 2000’s: 10 years on the tank (limited warranty, closed-loop heating) and 2 years on electrical and mechanical components, parts and accessories.
A 180 kW, 480 V VoltMax SCR, installed by AirGreen
Tell us about your project: we check the sizing, confirm availability and send you a quote. Or let our technicians install it for you.
Specifications from the manufacturer’s documentation, checked on October 19, 2026.
